Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:
+ j. [7 v8 p& z' p: N3 P

5 b0 {' V3 s$ e* t: h! iCould not connect to socket 9189 on host localhost
/ `! A7 e' F! d9 K- E3 V
+ J1 Y. O8 v4 V: u6 e; a. T6 jProbable causes:

1: The viewer is not running, or
2 w- R4 n+ }  I# ~% I8 k2: The viewer's server socket is not activated
" }- q  x3 H5 L
/ d0 \) @6 G4 T3 Q* c' O, a1 h
0 S) j& j! @- O% b# v" z# w請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
! p/ [1 h. u0 J. jvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
1 ]8 L1 P9 ]: \6 d) Q# Dlaker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
那是因為你的layout tool的port不是使用9189
2 z  d( H6 O- ~所以你無法將RVE的資料傳回layout
+ b5 c3 L1 Y0 }" o9 jvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

5 i) ~2 A8 ]% M+ L+ ^4 ~

我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
8 ^: s8 D6 S! ^. n, }                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer after invoking Calibre
( w' X/ N: |# U+ TInteractive, you can set up communication between the two tools through IPC sockets.
By default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
* H% {( e2 a/ L$ n4 l( ZYou can change the socket address used by following this procedure:
  \+ n9 H) l# \4 E! [1. Open the viewer.
7 a  {+ [: v. ^' l# B# J2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
3. In Calibre Interactive, choose Setup > Layout Viewer…
4. Enter the socket number that you activated in the viewer.
! ~+ j+ t  \( _$ a; N7 H2 Z4 G# J8 `5. Click Connect.
% H" C; L& ?, e0 z/ L6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
- l% [" J& Z5 x; Y1 C6 X# o# H+ pthe two applications is set up automatically. If you open a viewer a ...

& U+ ~$ T: U5 O. F- }) y
! s& N9 C& P% I( B
! ~! c# w+ t. w一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
它的socket number 有相同嗎?