用calibre要如何驗證所寫的command file是否正確

ckboy0928

想問一下，我用calibre要驗證所寫的command file是否正確，要如何下calibre驗證的語法呢?謝謝

dlnxx

LSW=>Edit=>Display Resource Editor
  V0 n, X2 T' `點選  "●ALL"  後，修改 y0 的顏色及是RVE error highline 的顏色
: g9 t3 _9 _, T8 sy2 ~ y9 為 "Mark Net" 功能的顏色

motofatfat

如果你有 GUI 功能
3 P4 K) r2 S# [1 T  G7 W* i先去 load command file
就能知道

shkao0201

關於calibre如何操作你可以看看/export/home/Calibre/ss6_cal_2005.1_10.20/shared/pdfdocs/calbr_inter_user.pdf
有詳細說明

shkao0201

在virtuoso 中 calibre DRC highline是可以在layout視窗
Calibre --setup---RVE 選取你要用來做highline的layer

ckboy0928

我目前是使用virtuoso layout tools,謝謝你!!

shkao0201

你是使用你一套layout tools??  比較好回答你的問題

shkao0201

virtuoso 要去修改LSW

8 e( i! c- P( e1 o在Laker預設中，Calibre highlight DRC錯誤的layer為system layer HLNet1 – HLNeta.如果想要讓highlight能夠閃爍，就必須更改這10層的設定

ckboy0928

在請問一下,如何改變Highlight的顏色,謝謝!!

shkao0201

setSkillPath(/export/home/Calibre/ss6_cal_2005.1_10.20/shared/pkgs/icv.ss6/tools/queryskl)
load("/export/home/Calibre/ss6_cal_2005.1_10.20/shared/pkgs/icv.ss6/tools/queryskl/calibre.skl")
& F1 x4 ^! J2 Q1 Y4 k
0 O' r2 J6 `7 O6 E以上是virtuoso 是要在.cdsinit中加入calibre的skill指令

shkao0201

基本上laker有將calibre的選單放入layout視窗中
virtuoso 則是要在.cdsinit中加入calibre的skill    才會出現在layout 視窗
操作上laker virtuoso 大同小異

shkao0201

你run 完 DRC 或LVS  要呼叫RVE的視窗,就可以DEBUG了.
* }) Y# E3 I% Z+ D  W$ e在DRC的視窗中--output--點選start RVE after DRC finishs.
/ b' ~, W& h3 L5 i6 `/ P在LVS的視窗中--output--點選start RVE after LVS finishs.

ckboy0928

在請問一下我所寫的command file 經過Compiler之後,如何得知哪條rule是對應到layout圖中某一區塊呢?
" q0 l0 z' l! I, U8 m* B7 {
我知道 Dracula是在Tools-->Dracula Interactive,在選DRC-->SETUP-->在設定run drc 路徑,就可知道哪條rule是對應到layout圖中某一區塊,不知calibre是否有此功能,那要如何點選才有這項功能

shkao0201

/export/home/Calibre/ss6_cal_2005.1_10.20/shared/pkgs/icv.ss6/tools/misc/rules_syntax_checker 這是我執行的目錄
/export/home/Calibre/ss6_cal_2005.1_10.20是calibre的安裝目錄
) q9 M" x' q% f8 I) y9 A) f你可以試試用which rules_syntax_checker去找出rules_syntax_checker放在哪
$MGC_HOME/shared/pkgs/icv.${VCO}/tools/misc/rules_syntax_checker中的$MGC_HOME/shared/pkgs/icv.${VCO}是你的calibre的安裝目錄喔
再試試看吧

ckboy0928

感謝這位大大提供,但是我照上面key in進去,結果出現
VCO : undefined variable訊息
  |7 {8 Q+ ?$ C請問要如何解決?
) @  u/ o% C  E: A3 M: N9 R8 F  U指令中的VCO代表何意?

shkao0201

1執行"$MGC_HOME/shared/pkgs/icv.${VCO}/tools/misc/rules_syntax_checker"
, z! r3 L" l2 k, o& A2 J3 @( A2給予commandfile.

shkao0201

Rules Syntax Checker
The rules_syntax_checker is a utility you can run on a rule file to validate the syntax of its
statements. The full path to this executable is
$MGC_HOME/shared/pkgs/icv.${VCO}/tools/misc/rules_syntax_checker. As shown in the
1 k7 x/ N0 r2 V. J0 c) k( c" K5 D% nfollowing example, this utility prompts you for the name of the rule file and then runs the check.
+ }% h7 I# D$ W6 o6 m" {It creates a zero length file named “compiled” if you answer “y(es)”.
rules_syntax_checker
" H! p7 N- C- O! h" I4 K0 ePlease input the file name (CTRL-D to abort): rule_file
* B' R$ W9 V& C% A( x4 p+ g+ C13-72 Calibre Verification User’s Manual
  |; I& I+ X+ Z$ }1 n: `Utilities
+ O, Z% z0 c' q. [  E7 w) qRules Syntax Checker
3 v8 V) n0 f7 J& x: z+ Y* OSuccessful compilation; compilation time = 0.02
You can also specify the pathname to the rule file upon invocation, as follows:
7 p& p2 A7 g6 g2 j" grules_syntax_checker rule_file
You may want to do this if you are writing a shell script to automate the process.
6 o9 [+ d: f7 U3 k) gEncountering an error terminates the check. The rule file compiler generates an error message
for the first such mistake it finds where the offending word sequence appears in the error
message. For example:
# ~. `7 Y) T+ X2 B; GError INP1 on line 15 of rule_file - superfluous or invalid input object:
0 u( {! I+ `. ySORCE.
After correcting the first such error, recheck the rule file to find the next error. Repeat this
process until the rule file generates no syntax errors.