proting IDE driver for uclinux/linux

tommywgt

我在Xilinx FPGA(EDK8.2)引用了MicroBlaze 32 bits RISC CPU, 可以RUN uclinux, 現在我又設計了一個非標準的IDE, 我自己寫個程式去R/W HD, 400G的也沒問題, 我也寫了一個FAT32 file system透過FAT32的LIB我所做的檔案操作, 使得HD接到WINDOWS也可以RUN的很正常. 但是問題來了, 這些自己寫的HD LIB無法跟uclinux KERNEL結合, 以致於無法直接跟系統資源結合, 也無法在VFS內mount這個device?

( W. }8 M6 N2 ]; O; z有人能夠清楚的詳列在LINUX下porting IDE driver的步驟嗎?

tommywgt

這一段是說明如何用ata driver改成sata, 照道理來講就是改drivers/ide這一段的code就對了.
有人能再補充更多的嗎?
) r& T7 j, Z5 J! E
7 u3 ]2 x# N& m, s3 j4 S) m4 NDriver Overview: Linux kernels have two ATA ("IDE") driver sets:

"drivers/ide": This is the traditional ATA driver set, maintained by Bartlomiej Zolnierkiewicz (before that, Andre Hedrick). Contrary to popular belief, it includes low-level drivers for many common SATA chipsets.

( ^$ h& Y5 q! X4 C. IOptionally, on top of drivers/ide block-device (generic mass storage access) drivers, one can load drivers to provide software-level suport for BIOS services enabling various types of manufacturer-specific software RAID (called "fakeraid", below):
$ N$ V9 J5 q. s
For 2.4 kernels, Linux's software-RAID (fakeraid) driver collection is called "ataraid", which has subdrivers for the various manufacturers' different software RAID schemes. Using ataraid results in your partitions being addressed using a /dev/ataraid/d0p1 (etc.) device-naming convention. Note: Support greatly improved circa-2.4.23.

$ _/ Y+ ~1 m* V* W1 DFor 2.6 kernels, Linux's software-RAID (fakeraid) driver collection is called "dmraid" (Device Mapper RAID). So far (Sept 2004), Promise Fasttrack, HighPoint 37X, Intel ICH5/6, LSI, and SiI 3112A/Medley are supported: http://tienstra4.flatnet.tudelft.nl/~gerte/gen2dmraid/
8 k. R# @- @$ Y' b; o
I'm pretty sure manufacturers' proprietary drivers, where available, are designed to fit the above framework.

"libata": This is the newer ATA driver set for selected SATA chipsets only, maintained by Jeff Garzik, leveraging the kernel's well-tested SCSI layer. Garzik developed it in the 2.6 kernel series. 2.4 support was available only with a backported patch until libata's inclusion in 2.4.27 and later.

libata causes each SATA port appear as a new SCSI bus. There are individual low-level drivers for the individual SATA chipsets, e.g., ahci, ata_adma, ata_piix, sata_nv, sata_promise, sata_sil, sata_sx4, sata_svw, sata_via, sata_vsc.

tommywgt

另外這有二個很重要的網站
# W  d; `, P8 F+ i8 p/ `www.t10.org SCSI
2 G2 T; H. t0 A3 v& V, \www.t13.org ATAPI

我在design HD controller時就是根據這二個網站資料的

kevin

我想你的問題是如何寫 Uclinux ide/ATA 的 driver.
% s, ^# Q7 W8 A. Z8 [可以參考O'Reilly "Linux Device Drivers" book.
code example 在 http://examples.oreilly.com/linuxdrive3/

tommywgt

好巧...這本書我有也...

( V' j- M: C; B不過還是謝了

大大願意在這跟大家分享的話論壇的後進都會感謝你的...

tommywgt

沒人回也...我自己推一下好了, 不然只好找時間自己回了...鳴

windflowerz

我隻能幫妳頂一下，非常抱歉，幫不暸忙哦

jacky002

因為你是用uCLinux，所以我首先會問你有沒有將MMU的設定關掉，在我記憶中uCLinux是不支援MMU的。
3 q/ i" ^" L3 @6 A$ s0 T
; {0 Y) z$ \- a  r其次，你是用ATAPI或是SCSI的driver layer去寫這個driver的。建議Driver path最好還是使用SCSI會比較好，其實底層都類似，只不過SCSI再上層多做了一層，轉了一層SCSI command，也補強之前ATAPI的部分不足。
2 H1 t3 w0 P: L8 L+ U- n% A  V+ z
給你參考，希望對你有所幫助。

olduncle

除了看書之外,最實際的方法就是參考别家的Source code
Linux的源碼就有很可供參考,不管是legacy IDE或是掛在SCSI下的libata
看個2~3隻driver,你就會清楚ATA的interface需要哪些structure及private function point.
而且Lnux本身就支援許多Filesystem,除非你是要hack filesystem,否則只要porting driver就夠了。

olduncle

除了看書之外,最實際的方法就是參考别家的Source code
. E: c$ E" E, w, ~5 V3 {6 cLinux的源碼就有很可供參考,不管是legacy IDE或是掛在SCSI下的libata
看個2~3隻driver,你就會清楚ATA的interface需要哪些structure及private function point.
0 O! d+ ?: |# v/ R( K3 o1 @而且Lnux本身就支援許多Filesystem,除非你是要hack filesystem,否則只要porting driver就夠了。