Chip123 科技應用創新平台

標題: Calibre遇到的問題 [打印本頁]
作者: dreamland    時間: 2009-10-29 05:32 PM
標題: Calibre遇到的問題
執行calibre時,出現了這個警告:
* \+ @0 N+ r# a- o. ]- ~( g
9 Z" U/ n+ Y  |9 b' S& }% L8 M8 W$ R+ }9 z& E5 g. r
Could not connect to socket 9189 on host localhost# N; ]3 C% A, W; ~: o
, m  X- l8 B# F
Probable causes:
# I3 J1 _9 E! D& `7 o  W: i" ?4 H3 w0 K  l
1: The viewer is not running, or  K4 |2 {% P' {1 o5 Y
2: The viewer's server socket is not activated
. u+ J1 ?) M/ C9 l; j* z" r* `+ i

5 l& m% j, B. A3 K請問有人遇過嗎?
作者: shkao0201    時間: 2009-10-29 05:51 PM
那是因為你的layout tool的port不是使用9189
5 S% h0 t$ l* ~" b* a! f) X7 d5 G所以你無法將RVE的資料傳回layout
; \& d# y( O" w5 Bvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
0 P: I! c( h; |laker:Verify---Calibre---Integrate with RVE---Server Port--->9189
作者: dreamland    時間: 2009-10-29 05:59 PM
原帖由 shkao0201 於 2009-10-29 05:51 PM 發表 5 o& |/ Y& }% @& c  y: }2 [% ~2 |* n
那是因為你的layout tool的port不是使用9189
6 h9 e1 Q# V% u* {5 f所以你無法將RVE的資料傳回layout
, o) `0 ]% r; f# Hvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189; e: a& J& G& C* H4 g
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...
3 F8 V5 t( d  F% U1 y; g
2 {- b$ F. |3 {( W0 n7 T" a* l6 ^) R/ O
, D  Z/ u* O2 f5 f; A
我使用的server port是9189
作者: shkao0201    時間: 2009-10-29 06:08 PM
試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
" r3 Z8 Q( w  a7 {                                                                                         ----IPC  settings--socket number-----9189
作者: shkao0201    時間: 2009-10-29 06:10 PM
然後你可以試試點Connect是否會出現Success.
作者: shkao0201    時間: 2009-10-29 06:12 PM
Setting Up Communication With a Viewer# Z9 [+ m7 W/ y- _) w
If you invoke Calibre Interactive from a layout or schematic viewer, communication between5 S  y- F+ s0 d: m, q) q: ]
the two applications is set up automatically. If you open a viewer after invoking Calibre5 Z7 O8 \" V' G$ X/ |- i
Interactive, you can set up communication between the two tools through IPC sockets.& R6 m4 z/ t/ V# i" c2 q
By default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
$ x& w: i2 |, [1 x2 }7 yYou can change the socket address used by following this procedure:
$ I. r+ ^! Y! r) e9 V0 b" m; D7 g1. Open the viewer.$ D7 ?, ~* b  K( u
2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.0 z  i. T' L  J1 }" |: `: |
3. In Calibre Interactive, choose Setup > Layout Viewer…
7 p' C0 f/ u+ j/ |4. Enter the socket number that you activated in the viewer.6 M+ u1 d( d6 x# i3 _8 M
5. Click Connect.
7 M1 t1 G' `# P6. Click OK. The figure shows setup of a layout viewer.
作者: dreamland    時間: 2009-10-29 07:35 PM
原帖由 shkao0201 於 2009-10-29 06:12 PM 發表 5 G0 H3 ]0 D- g8 J9 s& T
Setting Up Communication With a Viewer4 ~" ~$ X; B2 p7 j* W
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
$ s) d& J' q7 p2 L1 n; \the two applications is set up automatically. If you open a viewer a ...
1 i. l3 J2 q$ O1 K! \* V

5 W' P4 ~) Q) o9 w% X1 M/ j0 H; b) k9 Y! V0 C/ j  o
一樣不行用?
作者: shkao0201    時間: 2009-10-30 09:51 AM
你是試用laker去叫出RVE呢??, B; L$ e9 h/ L% z# r* y, g$ n
它的socket number 有相同嗎?



歡迎光臨 Chip123 科技應用創新平台 (http://www.chip123.com/) Powered by Discuz! X3.2